Structural Fire Damage Cleaning in Brainerd, MN
With the wallboard torn out, what is left is a skeleton of black studs, scorched rafters and smoke-stained block. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions puts you in touch with independent, licensed and insured Brainerd contractors who clean the bare structure down to sound wood.
- Soda, dry ice and hand cleaning of framing
- Every stud and joist probed for char depth
- Cleaned wood encapsulated against lingering odor
What Makes Framing Work Different
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
The contractors we connect you with are independent businesses carrying their own license and insurance. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Ask for a line-item written estimate before the first bag of media is opened.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Brainerd are free, and it is often the same day.
Blasting Rigs and Probing Tools
This trade runs on gear most remodelers do not own: soda blast pots, dry ice blasters, tow-behind compressors, HEPA vacuums, air scrubbers and an awl for probing char.
Stay out of a fire-damaged attic, and never walk a charred roof deck to check it. Burned joists and decking can fail under one person's weight, and open wiring may still carry current. Let the crew confirm the structure will hold before anyone goes up, and keep everyone off the floor above a burned basement or crawlspace.
Cleaning the Building From the Roof Deck Down
Furniture and debris are a separate job. It is the work done on the wood, block, brick and steel that hold your house up.
Char Depth Probing and Member Decisions
An awl pushed into a charred stud tells the story: if it stops in sound wood after a thin layer of char, the member is usually a cleaning candidate. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. It leaves a fine white dust and some residue, so containment and a thorough HEPA vacuum afterward are part of the job.
Dry Ice Blasting
With dry ice the pellets sublimate on impact, so there is nothing left on the floor but the soot itself. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. Hand work is slower but sensible where a blast rig would be too much.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Cleaned framing gets a coat of shellac-based or specialty encapsulant to lock in any odor left deep in the wood. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Have the contractor explain the method they plan for each part of the house. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Plan for containment, because blasting throws soot and media into every corner it can reach. Expect poly over openings, taped-off HVAC returns and air scrubbers pulling the space under negative pressure during blasting. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Brainerd. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Mention if a roofer, engineer or adjuster has already been out.
- 2
Mobile Crew on Site
The contractor arrives with a compressor, blasting equipment and containment materials. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
Once the wood is blasted, vacuumed and sealed, the crew lead walks you through the open structure. Smell the space on a warm day and get photos of each tagged member before anyone hangs drywall.
What Callers Said About Their Structural Crew
The attic fire left every rafter black and the insulation soaked. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
I assumed every black stud in the hallway had to be replaced. The crew lead probed each one with an awl and showed me that most were just surface char. They soda blasted and sealed them, and only three were swapped.
Our basement fire blackened the block walls and the steel beam over the family room. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. No smell now, even with the windows shut.
Your Structural Fire Cleaning Questions Answered
How do crews decide if a charred stud can stay?
The test is simple: they probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealing dirty wood does not work, so the cleaning has to come first.
Does the attic insulation have to come out after a fire?
If smoke reached the attic, almost always yes. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. It is vacuumed out with an insulation vac so the rafters and roof deck can be probed, blasted and sealed before anything new is blown in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. The building department may ask for it before signing off on the rebuild.
Charred Framing Cleaning Across Brainerd and Beyond
Our dispatch line covers Brainerd and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
If the first crew we connect you with is not the right fit, call back and a dispatcher will connect you with another. Do not let the rebuild close walls over dirty framing.
